Water Cooled Spindle Kit 2.2KW CNC Milling Spindle Motor + 2.2KW VFD + 80mm Clamp + Water Pump Pipe
[2041841053] Water Cooled Spindle Kit 2.2KW CNC Milling Spindle Motor + 2.2KW VFD + 80mm clamp + water pump/pipe +13pcs ER20 for CNC Router Package include: 1 x 2.2KW CNC Water Cooled Spindle Motor 1 x 2.2KW/220V VDF 1 x 3.5M Water Pump 1 x 5M Water Pipes 1 x 80mm Spindle Clamp 13 x ER20 Collet (1,2,3.175,4,5,6,7,8,9,10,11,12.7,13mm) Notice : there are two types of frequency converter , HY type is better shell and the mainboard . package for no cable : 1piece 2.2kw inverter+ 1piece 2.2kw water cooled spindle+1piece water pump+ 1 piece 5m water pipes+1piece 80mm clamp+13pcs ER20 package with 2m cable: 1piece 2.2kw inverter+1piece 2.2kw water cooled spindle+1piece water pump+ 1 piece 5m water pipes+1piece 80mm clamp+13pcs ER20 + 2m cable package with Cutters : 1piece 2.2kw inverter+1 piece 2.2kw water cooled spindle+1piece water pump+ 1 piece 5m water pipes+1piece 80mm clamp+13pcs ER20 +10pcs cutters package with Brush:1piece 2.2kw inverter+ 1 piece 2.2kw water cooled spindle++1piece water pump+ 1 piece 5m water pipes+1piece 80mm clamp+13pcs ER20+100mm brush package with cutters cable brush: 1piece 2.2kw inverter+1 piece 2.2kw water cooled spindle+1piece water pump+ 1 piece 5m water pipes+1piece 80mm clamp+13pcs ER20+2m cable +10pcs cutters+ 100mm brush Warranty :1 year from the date you purchased!! Pictures: Basic Date 1. CNC Spindle Motor Size:80mm Power:2.2KW Voltage:220V Frequency:0-400Hz Speed:0-24000rpm Water Cooling ER20 collet Runout off:less than 0.005mm Grease Lubrication 4pcs bearing C7005X2 C7002X2 Preparations before using 1.Spindle working environment temperature is usually -10 ~ 40 . 2.Before installing the first electric spindle axis head turned by hand, should feel flexible, non-blocking phenomenon. About spindle using: 1.Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the poor increase, run 20 minutes each. Spindle and the inverter should be working together. The inverter's specifications and parameter settings need match spindles parameter. 2.Connect the inverter spindle, three-phase inverter power cord should be soldered in the plug 1 (U), 2 (V), 3 (W) feet, 4 feet for the ground. After the power is turned on, to observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle connected two wires of three-phase power supply. 3.It should ensure that before use of water-cooled spindle, the cooling system is working properly. Every day before using the spindle must be running at low speed for 15-20 minutes. Clamping the cutters to spindle, collet nuts ,collets,cutters must be clean enough. Shank inserted into the collet must be greater than 15mm. Care and maintenance 1.Water cooled spindle MUST be used with water pump. Otherwise the spindle will soon broken. 2.AC spindle motor MUST use with inverter. The power of inverter need equal or bigger than the spindle power. Before using,please set up the inverter parameters suitable for spindle. Otherwise the spindle and inverter will broken at once. 3.When you use the spindle,the noise is not same as always,please STOP the spindle at once. You may need to replace the spindle bearings. PID control; advanced calculus PID closed-loop arithmetic, quick responding speed and high suitability; 2.Inverter Type:2.2KW/220V Input:220VAC/50Hz Output:0-220VAC 3-phase Frequency:0-400Hz the parameter of the inverter is : PD005=400 PD004=400 PD003=400 Inverter Feature 1.Easy PLC function can realize 16 legs of speed and inverter control function; 2.RS485 communication port, adopting standard international MODBUS main circuit control; 3.With extremely strong anti-jamming capability 4.Low output ratting torque0.5HZ-150%, low speed running ability; 5.Carrier adjustable by 16KHZ, completely soundless working environment; 6.Broad voltage working area, normal running in 304V-456V; 7.Auto voltage regulation (AVR) technique, for ensuring the inverter load capability; 8.Various control technique by both synchronization and non-synchronization, dynamically realize fast starting without changing brakes; 9.With perfect error protection and short circuit starting protection capability; 3.water pump Special engraving machine spindle motor cooling water pump, 3.5m, 80w high power! Voltage: 220v (can be directly connected to the household power supply) Head: 3.5 m Flow: 3500L / h Power: 80w Usage: placed directly after the pumps and pipes connected to the tank, the tank water level height should be more than 2.5 times the height of the pump of the best! Avoid dry dry! 4. collet : 1set er20 13pcs (1,2,3.175,4,5,6,7,8,9,10,11,12.7,13mm) 5. clamp: 80mm clamp 6. 5M Water pipe: Size:5M 6mm (ID)*8mm (OD) If you want to purchase ITEMS from China, please give me your product list, let me give you a quote. Our company is focused on providing CNC /3D PRINTER parts and accessories. We have our own cnc processing plant, and cooperate with some other factories, this will help control costs and ensure quality. Friend, We really hope to be your < CHINA SOURCING AGENT >, make your China sourcing work more convenient and efficient!
US $287.14Limited Time 33% US $192.38
Tidak ada komentar:
Posting Komentar